Dishwasher Repair

Why a Washing Machine Won't Spin, and What to Check First

By , founder & appliance technician

June 15, 2025 · 8 min read
Washing Machine Not Spinning Wet Clothes

A newer washer will stop the spin on purpose, so that may be all yours is doing. The control won't start spinning while there's water left in the tub. It won't spin if the door isn't locked, and it holds a lopsided load back too. That keeps the floor from getting soaked and stops the machine shoving itself across the floor and into the wall.

We list it two ways on our washer repair page. One of them is clothes that stay too wet. A machine that quits before the spin cycle finishes is the other. Stick around near the end of a cycle and watch the last few minutes. The first thing is whether the water drains out of the drum. Then look for the drum rocking side to side and stopping. A machine that just sits there and does nothing is worth noting too. Those three results each point us to a different group of parts.

Water left in the tub: the drain side

Clothes left sitting in water when the cycle ends tell you the water couldn't get out. The drum speeds up only once the control sees the water level drop. Open up the pump filter and check it for lint or coins packed inside. After that, check behind the cabinet for a bent drain hose. Sludge can back up the standpipe as well, so take a look at it. Listen to the pump as you check. Sometimes you'll hear it hum or click while no water comes out at all. Plenty of these clogs are caused by socks and other small things. You can read where they go in our article on why socks disappear in the dryer and the washer.

The pressure sensor can't tell foam from water. To the sensor, a drum full of bubbles looks like a full tub, so once in a while the spin stops just because of too many suds. When thick foam shows up behind the door glass, too much soap is usually the reason. You'll find the right dose for HE machines in our guide on how much laundry detergent to use.

The drum rocks but never speeds up

This one is the balance sensor doing its job. Before anything else it tries to even the load out. When that fails, it cancels the spin. Often the cause is one heavy item. It could be a bath mat, or a single pair of jeans washed on their own. Very small loads do this as well when they end up in one wet clump in the drum.

An even load with a drum that still won't spin means the machine itself is next to look at. If the cabinet's off level, the tub can swing far enough to trip the sensor. On front-loaders, worn shocks and springs will cause that as well. Top-loaders have suspension rods instead, and they wear the same way. While it tries to pick up speed, the tub bangs against the cabinet. You'll hear it. Loud banging during spin is on our washer repair page, in the list of noise complaints. The first thing to do is adjust the levelling feet so the washer sits level on the floor.

The door lock and what the display says

Your washer has to lock its door before it'll spin. Every one does. You'll hear a firm click from the lock on a front-loader once it engages at the start of the cycle. There's often a second click right before the spin as well. A blinking lock light likely means the door lock assembly is at fault, and so does a cycle that stops just where the spin should begin. With a top-loader it's a switch or a latch under the lid that does this job.

Take a close look at the display. With an LG washer, UE is an unbalanced load, OE means a drain fault and LE points to the motor. The rest of them are listed on our page of LG washer error codes. Whirlpool front-loaders use a separate set of codes of their own. We explain those in our Whirlpool washer codes guide. When you've written the code down, give us a call.

Drain and lock are fine: the motor side

Once in a while a washer drains its water and locks the door, and the load's spread out evenly too. The drum still doesn't spin. When that happens, the fault is in the drive or the electronics. Both are under Motor or Pump Issues on our washer page.

Washers with a belt drive can throw the belt or snap it. LG is known for its direct-drive front-loaders, where the motor and a rotor position sensor both need to work. Either one failing keeps the drum from getting to high speed. Some top-loaders have a clutch or shifter that wears out. The agitator keeps working fine, but the basket stops turning.

Switch off the power. Once the power's off, turn the empty drum by hand. Grinding or a gritty feel while it turns likely points to the drum bearings. That's a bigger job to change, so it needs a proper quote before anyone starts on it.

Three checks that are safe to do

Stop the cycle and give the door time to release. Shake the load around so it sits evenly. A single heavy item on its own needs a towel or two in with it to even things out. After that, pick drain and spin and run it by itself. Take a look behind the washer while it's running. The drain hose might have been flattened when the machine was pushed back. A lot of front-loaders also hide the pump filter behind a small hatch low on the front of the machine. The manual shows how to drain it, and you will need a shallow pan and plenty of towels.

Stop running full wash cycles on the machine if the drum still won't spin after these steps. It strains the pump and the motor each time it tries to spin a waterlogged load.

Booking a washer repair

Before anything else, the technician looks at the drain path and the lock. The motor and control wait until last, so the simple causes get ruled out ahead of the costly ones.

Therese M from Ottawa wrote: “Excellent customer service. Gave a 2 hour window of when he would arrive and came on time. Looked at my washer draining problem and had it repaired in no time flat. Rate was exceptionally reasonable. I highly recommend Sergei and his company. He is certainly going to be my go too appliance repair man in the future.”

Stittsville and Carleton Place sit close to our Kanata base, and most repairs are finished on that first visit. Book washing machine repair online and save $30, or call (613) 869-0101 and the service call is free once you approve the repair; the two offers don't combine. Whatever part goes in, our 90-day warranty on parts and labour starts the day of the repair.

FAQ

Check two things first, an unbalanced load and a door lock that never engages. When the load is even and you hear the lock click, the belt or the motor drive comes next.

Unplug the washer for about a minute and then plug it back in. Spread the load out and select drain and spin. The washer may still not spin after you have done this. Make a note of any code that appears on the display and give us a call.

A handful of clothes tends to roll into one heavy wad on one side of the drum, and the balance sensor calls off the spin. Add two towels to the drum to even out the weight.

Yes, using too much detergent can cause this problem. The level sensor reads foam as water, and foam also slows the drain, so the spin can be delayed or skipped. Go by the load size when you measure detergent, and put HE detergent in an HE washer.

More from the blog

Learn How to Help Your Dryer Work as Long as Possible
Dryer Repair 6 min read

Learn How to Help Your Dryer Work as Long as Possible

To ensure your dryer works efficiently and lasts for years, your maintenance habits are crucial. Discover the best practices, including cleaning the lint filter before every cycle and dividing laundry by fabric weight. These simple strategies, combined with using lower heat and air drying when possible, will maximize your machine's lifespan and save energy.

Read article
100%
Guaranteed

Same-day service across Ottawa, flat-rate pricing, and every repair backed by our warranty.

(613) 869-0101