Reading Bosch Dishwasher Error Codes, E12 to E25

4.9 out of 5 · 244 Google reviews
(613) 869-0101
Same-day service 100% guaranteed Licensed & insured

Bosch dishwasher logo

Bosch dishwasher error codes show up on the display as E24, or E:24 on some models. It means the same thing. Basically the dishwasher stopped the cycle. The code points you to the system that flagged it.

You won't get the exact failed part from the code. A technician tracks down the faulty part. Below you'll find codes E12 to E25 and the simple checks that are safe to try at home: cleaning the filter, opening the water tap and straightening a kinked hose. Most of the detail is on the two drain codes and the leak code.

Before you look up the code

Write down the code shown on the display before you do anything else. Once you reset the dishwasher the code is gone from the display, and our technician will ask you for it.

Cancel the program using the steps shown in your owner's manual. Next, run the dishwasher again and see whether the code returns in the next cycle. When the code stays away after the next run, it may have been a pan that flipped over onto the filter during one cycle. The same code on the next run means there's a real fault, and resetting it again won't fix it. Keep running a machine with a leak or drain fault and you may be mopping the floor.

Bosch dishwasher error code table

The steps listed in the third column can be done without any tools and without opening a panel.

CodeWhat it meansWhat you can checkCall a technician when
E12Limescale buildup in the heat pumpRun a Bosch descaler to remove hard water depositsThe code returns after descaling
E14Flow meter failure, or a problem with water flowing into the dishwasherCheck that the water tap under the sink is fully openThe tap is open and the code stays
E15The safety switch has found water in the base; leak protection is onUnplug the machine and close the water tapAlways; the leak has to be found
E16, E17Problem with water filling the system; water may not be able to enterCheck that the water tap is openThe tap is open and the code stays
E18Water level too low, or water not pumped correctlyCheck that the tap is open and the inlet hose behind the machine isn't kinkedThe tap is open, the hose is straight, and the code stays
E22Filter blockedTake out the filter and clean itThe filter is clean and the code comes back
E23Drain pump blocked, clogged or faultyClean the filterThe filter is clean and the code comes back
E24Not draining properly; often a blocked drain filterClean the filter, check the drain hose for kinks and check the garbage disposal plugThe tub still holds water after these checks
E25Drain pump blocked, or the pump cover under the filter is loose or missingClean the filterThe filter is clean and the code returns

E24 and E25: the drain codes

E24 means the water didn't leave the tub the way it should. On a Bosch the filter is set into the bottom of the tub, a cylinder with a flat mesh plate around it. The most common cause is grease and food collecting on that mesh, so twist the filter out and rinse it under the tap. After that, check the drain hose behind the machine for any kinks. The next check applies if the dishwasher is connected to a new garbage disposal. Then check that the plug in the disposal's dishwasher inlet was knocked out. If the plug is still in place, the code appears from the very first cycle.

E25 points lower, to the drain pump. Once the filter is out, there's a small plastic pump cover at the bottom. The cover only has to be loose or missing to trigger this code. It also shows up if a piece of broken glass or a fruit pit gets stuck behind it and jams the impeller. Checking and refitting the pump cover is part of our technician's visit, since debris behind it can be sharp.

If water is still sitting in the tub after you have checked the filter and the drain hose, more checks are needed. Our guide on water not draining from the dishwasher walks through the rest of the drain path.

E15: water in the base

Under the tub of a Bosch there's a shallow base trough with a safety switch in it. When water collects in the trough, the switch is triggered and the leak protection system activates, and this is when E15 appears on the display. The water in the trough has come from inside the dishwasher.

The first step is to unplug the dishwasher and close the water tap under the sink. If the code is cleared and the leak is not found, E15 will come back on the next cycle. Our article on a dishwasher leaking explains how to tell where the water's coming from.

Filling codes and E12

E14 and E16 to E18 all have to do with water coming in. The first things to check are outside the dishwasher. Check that the tap under the sink is fully open and that the inlet hose behind the machine is not pinched against the wall. If both are fine and the code does not go away, the cause is inside the dishwasher, and a technician will need to test the parts with a meter.

The E12 code is caused by hard water. Limescale has built up in the heat pump. Bosch recommends its own descaler for this.

When to call a technician about a Bosch dishwasher code

E15 on the screen is a reason to call. You should also call if an E24 or E25 code keeps coming back after the filter has been cleaned. At that stage the repair work is behind the kick plate, close to the wiring.

We provide Bosch dishwasher repair across Ottawa from our base in Kanata, and same-day service is available. Every job we complete comes with a 90-day warranty on both the part and the labour. When you call, tell our technician the code you wrote down, and you will be told what the problem is and what the repair involves. You can reach us by phone at (613) 869-0101. Other brands: see our dishwasher repair in Ottawa page.

FAQ

Follow the steps in your owner's manual to cancel the program. When the fault's still there, the same code shows up again on the next cycle.

The code shows up when water isn't draining properly. So the first job is to pull the filter out and clean it, and after that check the drain hose for kinks. Check the disposal as well if the dishwasher is connected to a new one. Its dishwasher inlet plug may still be in.

E24 is the general drain fault and a clogged filter is often behind it. E25 is about the drain pump itself. It may be blocked, and sometimes the cover is loose or missing.

Leave the dishwasher off while this code is on the display, because the safety switch has found water in the base of the dishwasher. Unplug it and shut off the water tap, then find the leak before you run it again.